Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Bedford
Gate parts and welding in Bedford usually means one of two calls: a wood driveway gate dragging on the latch post after a wet winter, or an ornamental iron gate that finally cracked at a hinge weld after 35 years of North Texas clay heave. We handle both, and everything between. Gatewood Fence & Gate has been owner-operated since 2001, and when you call (817) 241-4067, a live person picks up. Not a voicemail. Not a phone tree. You’ll talk to someone who knows Bedford’s streets and knows why your gate is failing.
We weld on site, in your driveway. The gate doesn’t leave your property. That matters in Bedford, where most gates are 30-50 years old and the soil under them has been moving since the day they were set.
Key Takeaways:
- On-site welding and parts replacement for wood and iron gates across Bedford
- Post reset and gate realignment are the real fix for most Bedford sagging gates, not hinge swaps
- We service Ghost Controls, DoorKing, Elite, and Mighty Mule operators
- Free estimates, upfront pricing agreed before any work starts, 90-Day Done Right Promise in writing
- Call (817) 241-4067 any time, day or night
Why Gatewood Fence & Gate Is Bedford’s Preferred Gate Parts & Welding Company
Reputation in this line of work is built one gate at a time, and Bedford homeowners talk. They compare notes at the Stonegate HOA meeting and over fences on Donna Lane. When a neighbor’s gate finally swings right after three other companies “adjusted” it, people ask who did the work. That’s how we’ve grown in Bedford without a billboard.
The person who gives you the quote is the person doing the welding. Hal Gatewood’s name is on the shop, and the shop is down the road. That’s the oldest accountability there is. We’re not a franchise with a rotating cast of subcontractors. We live in this metro, we know the clay, and we know that a gate sags in the hinge post, not in the middle. That’s where we start.
Scheduling from our Dallas-Fort Worth office means Bedford calls get a straight answer on arrival windows. We tell you when we’ll be there, and we’re there. Our 90-Day Done Right Promise is stamped on every invoice. If it’s not right, one call brings us back. No runaround.
Our Gate Parts & Welding Services in Bedford
Hinge Replacement
Hinges on Bedford gates fail in predictable ways. Wrought iron barrel hinges crack at the weld after decades of the gate pulling against a heaving post. Wood gate hinges pull loose when the post twists and the screws strip out of soft cedar. We stock heavy-gauge weld-on barrel hinges and heavy-duty strap hinges suited to Bedford’s older gates. We don’t bolt a new hinge onto a post that’s out of plumb. We fix the post first, then the hinge. A hinge swap on a leaning post is a waste of your money and ours.
Post Replacement
This is the most common structural repair in Bedford, and the most skipped one. Most posts in this city were poured before current clay-soil practices existed, and decades of shrink-swell cycles have worked them loose or out of line. We dig out the old footing, set the post plumb, and pour a new collar clear of root intrusion where mature oaks have pushed into the hole. A new post job in Bedford typically includes re-hanging the gate and aligning the latch so everything works as one unit.
Rail Repair
Wood gate rails split where hinge screws bite in, and iron rails crack at weld joints where a heavy gate overworks a thin section. We weld iron rails solid and scab or replace wood rails with pressure-treated stock that matches the gate. On ornamental gates, we grind out the old crack, weld it properly, and repaint the repair so it blends. If the rail failed because the post moved, we address that first. Fix the panel without the post and you’ll fix it twice.
Custom Welding
Some Bedford gates don’t have a replacement part anymore. The manufacturer is gone, the design is from 1984, and nobody stocks a bracket shaped like that. That’s where our on-site welding earns its keep. We fabricate hinge plates, gussets, reinforcement brackets, and even full bottom rails in place. Custom welding keeps an original gate in service instead of hauling it to the scrap pile. Hal has been welding gates since 2001. There isn’t much he hasn’t fixed in a driveway.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Bedford
We’re certified to work on nine major gate opener brands, and the ones we see most in Bedford are Ghost Controls, DoorKing, Elite, and Mighty Mule. Older Bedford subdivisions are heavy with builder-grade DoorKing and Elite units from the 1990s, and those need a technician who understands their trip settings and torque curves. We stock common parts for those brands so Bedford repairs don’t wait on a slow parts shipment. If it’s a brand we service, the part is either on the truck or a day out.
Common Gate Parts & Welding Problems We See in Bedford Homes
- Clay heave pushing posts out of plumb. Bedford sits on Blackland Prairie clay that swells in wet winters and shrinks in summer droughts. Every cycle works the post a little further off line until the gate drags or the latch misses. A sag correction only lasts if the post is reset first.
- Root intrusion under fence lines. In neighborhoods platted in the late 1970s and 1980s, mature post oaks and cedar elms have pushed surface roots under gate footings for 40+ years. The post lifts, the concrete collar cracks, and no hinge adjustment fixes it until the footing is dug out and repoured clear of the roots.
- Builder-grade operator lockouts. 1990s Bedford subdivisions often came with entry-level LiftMaster or Elite operators. When the gate post shifts even a few degrees, the arm geometry throws out of spec and the motor locks out under torque. The operator isn’t dead; the post moved.
- Slide gate rollers cracking under root pressure. Cedar elm roots run shallow and lift roller channels on backyard slide gates. The gate jumps the rail, the rack-and-pinion gears strip, and the opener fails. Fixing the roller channel is the real repair. Replacing the gear without it means you’ll be replacing it again.
Pricing for Gate Parts & Welding in Bedford, TX
Here are the ranges we quote for Bedford work. Hinge replacement on a wood or iron gate usually runs $150-$350 depending on how many hinges and whether the post needs realignment. A full post replacement with new footing runs $400-$900 per post, and that includes re-hanging the gate and aligning the latch. Custom welding repairs like gusseting a cracked rail or fabricating a hinge plate run $120-$400, and we can usually look at a photo and give you a firm number before we arrive. If we’re already on site for a post, we’ll inspect the hinges and latch and quote any additional work in writing first.
The price we quote is the price you pay. We write it down and we agree to it before any work starts. You’ll never open an invoice that doesn’t match the estimate. Estimates are free, and if you’re inside the county, so is the trip. Call (817) 241-4067.
We Also Serve Cities Near Bedford
We’re based in the Mid-Cities and run calls through Colleyville, Hurst, North Richland Hills, and Haltom City every week. If you’re in one of those cities, the same Gate Parts & Welding service applies, and the trip charge rules stay simple. Our Bedford customers usually see us the same day or next morning.
Serving Bedford, TX - Our Local Coverage Area
We’re based in the Bedford area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Bedford
Because the post is moving, not the hinge. Tightening a hinge on a post that’s out of plumb does nothing. Bedford’s clay soil heaves and shrinks every year, and over 30 to 50 years that movement works the post loose. The fix is a post reset: dig out the old footing, set the post plumb, repour clear of root intrusion, and re-hang the gate. Then the hinges stay tight. Call (817) 241-4067 and we can tell you over the phone whether it sounds like a post problem or a hinge problem.
Yes, with one condition: the gate and post have to be structurally sound first. An opener motor on a sagging, out-of-plumb gate burns itself out fast. We inspect the post, hinges, and gate weight before recommending an operator. If the structure is good, we can add a Ghost Controls or Elite opener sized for the gate’s weight and cycle frequency. Many Bedford gates from that era are solid enough; they just need a post reset first.
Usually it’s the track bed, not the rollers. When Bedford clay swells after rain, the ground under the roller channel shifts and the channel warps or lifts. The gate runs off the rail and the opener strips a gear trying to push it back. We inspect the channel and footings before replacing any rollers or gears. Fix the rail, replace the rollers if they’re chewed up, and the gate runs smooth again. Call (817) 241-4067 for a free estimate.
Yes, and we won’t add an operator without it. Any automated gate needs to stop or reverse if something is in the path, and modern UL 325 compliant operators include obstruction sensing. Gates are heavy enough to hurt someone, and that’s not a corner anyone should cut. We install entrapment protection on every automation job in Bedford, no exceptions. If a company quotes you an opener without it, get a second opinion, ours is free.
Cracked hinge welds and broken bottom rails where a heavy wood or iron gate has been dragging for years. Bedford’s clay heave puts constant stress on hinge welds, and once one crack starts, the rest of the gate gets loaded unevenly. We grind out the crack, weld it properly, and often add a gusset so it doesn’t crack in the same spot next year. It’s a repair that keeps the original gate in place, which is usually what Bedford homeowners want. Call us for a firm quote before you decide to replace anything.
Contact Gatewood Fence & Gate for Gate Parts & Welding in Bedford
If your Bedford gate is sagging, dragging, cracking, or just won’t stay shut, call (817) 241-4067. A live person answers, any time of day. We’ll ask what the gate is doing, give you an honest read on what it needs, and set a time to look at it in person. The estimate is free, the price is agreed before work starts, and the 90-Day Done Right Promise comes with the job in writing. We’ve been at this since 2001, and Hal Gatewood’s name is on every invoice. That’s how it should be.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Bedford since 2001.