Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Installation Across Haltom City
Gate installation in Haltom City usually means one of two jobs: either a 1950s-era chain-link swing gate on a ranch lot off Carson Street needs full replacement before it falls off its hinges, or a commercial slide gate on Denton Highway has finally seized up after 30 years of neglect. We handle both, often on the same day. Hal Gatewood has been welding and hanging gates since 2001, and he’s seen every failure mode Tarrant County clay can throw at a post footing. If you need a straight answer about whether to repair or replace, call (817) 241-4067 and you’ll talk to a person who actually installs gates, not a call center.
Why Gatewood Fence & Gate Is Haltom City’s Preferred Gate Installation Company
Haltom City is our kind of place. The streets here mix postwar ranch homes with auto body yards, paint shops, and small manufacturers, sometimes on the same block. That means the gate on a 1960s house off Broadway Avenue might sit three doors down from a 40-foot slide gate guarding a warehouse loading bay. Most gate companies specialize in one or the other. We do both because we live and work in this exact patchwork. Hal’s name is on the shop and on every invoice. His address is published. You can drive to his shop, look him in the eye, and hand him a gate problem nobody else wanted to touch.
Every estimate is free, every price is agreed before work starts, and every job carries the 90-Day Done Right Promise in writing. Not “up to 90 days.” Not “in most cases.” If it’s not done right, one call brings Hal back. We also answer the phone 24 hours a day with a live person. Not a voicemail tree, not a bot. That matters when your security gate won’t close at 9 p.m. and your driveway is wide open to the street.
Our Gate Installation Services in Haltom City
Here’s what we actually install across Haltom City, from residential backyards to commercial entries off TX-26.
Driveway Gate
A driveway gate on a Haltom City ranch home has to hold alignment through brutal clay movement, summer droughts, and spring downpours. We install swing and slide configurations suited to your lot slope and setback. Many Haltom City driveways are shorter than newer suburbs, so we often recommend a compact swing gate operator rather than a long-track slide system. Every install includes properly set posts, correct hinge hardware, and a written quote before we dig a single hole.
Pedestrian Gate
Small lots mean most Haltom City homes have a walk gate next to the driveway, usually chain-link and usually original to the house. We build pedestrian gates that don’t sag after one rainy season. That means a deeper post footing than whoever installed it in 1962 bothered to pour. If you want a keypad or electronic strike on a walk gate, we’ll wire it clean and make sure the latch releases reliably every time.
Sliding Gate
Cantilever slide gates are standard for Haltom City industrial tenants along Denton Highway and the light-manufacturing corridors. These gates run on rollers over concrete pads, and years of deferred service leave wheels flat-spotted, tracks packed with debris, and chain drives slapping. We measure, spec, weld, and install cantilever and V-track slide gates built for daily operation, not decorative show, with Gate Parts & Welding in Haltom City available when your frame needs more than adjustment. If your existing slide gate from the 1980s still has a working frame, we’ll tell you honestly whether a retrofit makes sense or replacement costs less over five years.
Swing Gate
The swing gate is the default for Haltom City’s residential streets, and it’s the style we see fail most often. Two leaves, a center latch, hinge posts set in expansive clay. The fix starts at the post, never at the panel. We cut out rusted galvanized frames, set new steel posts deeper than code minimums in Tarrant County soil, and re-hang the gate with hinges rated for the leaf weight. Add an operator only after the gate swings freely by hand. That sequence is the difference between a gate that lasts and one that eats gearboxes every two years.
Trusted Brands We Service in Haltom City
We install and service operators from LiftMaster, DoorKing, Elite, Ghost Controls, and Mighty Mule. That matters because Haltom City’s older gates often carry control boards that are obsolete but still repairable if you know the wiring. We keep common boards, safety photocells, and limit switches stocked locally, so a gate on Carson Street isn’t down for two weeks waiting on a part from a distributor two states over. That’s part of our Gate Access Control in Haltom City service: working electronics, not just working iron. When the brand on your existing opener is long discontinued, we’ll tell you whether a retrofit kit keeps it running or a full operator swap is the honest answer.
Common Gate Installation Problems We See in Haltom City Homes
- Heaved posts from Tarrant County clay. The shrink-swell Vertisol soil here expands when wet and contracts in drought. Posts set shallow in the original installs tilt, heave, and drag your gate out of latch alignment by late summer. We set new posts in deeper footings and use concrete mixes suited to the soil, not what a big-box store sells off the pallet.
- Rusted galvanized pipe frames on 1950s-1970s chain-link gates. The original gate on many Haltom City ranch homes is a pipe frame with welded corners. Forty years of North Texas humidity and sprinkler overspray leaves the bottom rail paper-thin. You can patch it, but a welded steel replacement frame often costs less over a decade than three repair visits.
- Obsolete control boards on 1980s and 1990s commercial slide gates. Along Denton Highway and the industrial pockets off Carson Street, we see chain-drive slide gates that haven’t been opened for service since they were hung. The board fails, then the chain jumps, then the gearbox strips. Deferred maintenance turns a $400 board into a $4,000 gate replacement. We give you the honest repair-or-replace math before touching a wrench.
- Operators added to gates that were never retrofitted for safety. UL 325 requires monitored photocells, force settings, and edge sensors. An old chain-link gate with worn hinge pins and no safety edges is a liability, not just an inconvenience. We retrofit the hinges, the posts, and the safety system together so the gate isn’t a hazard to a kid or a delivery driver.
Pricing for Gate Installation in Haltom City, TX
A typical residential single-leaf swing gate installation in Haltom City runs $900 to $2,400 depending on width, material, and whether you’re adding an operator. A double-leaf driveway swing gate with a LiftMaster or Mighty Mule opener typically lands between $2,800 and $5,500. A commercial cantilever slide gate with a DoorKing or Elite operator starts around $4,000 and can top $9,000 for a wide, heavy-league industrial unit. The wildcard here is always the post footing: Haltom City’s clay means some jobs need deeper excavation and more concrete than a flat-soil install. That’s in the written quote, not a phone call surprise. On residential installs we honor our standing offers: $40 off any repair over $200, no trip charge inside the county, a free second opinion on any written estimate, and a permanent 10% discount for seniors and veterans. Call (817) 241-4067 for an exact quote before we do anything, and that’s the number you’ll pay. Every job, in writing, agreed before the first post hole.
We Also Serve Cities Near Haltom City
While this page focuses on Gate Installation in Haltom City, our crews work the surrounding area daily. We install and repair gates in Fort Worth, North Richland Hills, Hurst, and Bedford. If you’re a few blocks over the city line, call (817) 241-4067 and we’ll schedule you the same way. No trip charge inside the county applies in all these cities.
Serving Haltom City, TX - Our Local Coverage Area
We’re based in the Haltom City area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Installation in Haltom City
The answer depends on the frame condition and the hinge posts, and around Haltom City the posts are usually the failure point. If the galvanized pipe frame is still solid and the posts haven’t heaved more than a fraction of an inch, we can retrofit a LiftMaster or Ghost Controls swing arm with new hinges and safety photocells, often for under $1,200. If the bottom rail is rotted or the post wobbles when you push the gate, an operator will rip the hinges out within a season. We’ll give you an honest read in the first visit. Call (817) 241-4067 and we’ll come look at your exact gate before recommending anything.
That’s the Tarrant County clay doing what it does. The Vertisol soil under your post expands with spring moisture and shrinks hard during summer drought. A post set in a standard-depth footing moves enough to shift the gate leaf down and out, so the latch gap widens or the bottom rail scores the driveway. The permanent fix is a deeper steel post set below the active clay layer, then re-hanging the gate with new hinges and a sag correction. The temporary fix is adjusting the latch, which fails again by next summer. Call (817) 241-4067 for a free estimate on the permanent one.
Yes, and we retrofit older operators to meet UL 325 whenever we touch a gate. That means monitored photocells, force-limiter settings, and edge sensors where required. A 1990s slide gate on a Haltom City industrial lot without photocells is a serious safety hazard and a code violation. We stock the retrofits for DoorKing, Elite, and older Linear boards, and we do the wiring in-house. Call (817) 241-4067 for a free safety assessment on any gate you’re worried about.
First we core or excavate to see what the existing footing actually looks like. In Haltom City’s clay, many 1980s industrial gate footings are shallow and cracked. We’ll size a new concrete pad and cantilever footing based on the gate weight and daily cycle count, not a generic spec. Then we build and weld the gate frame, hang it on rollers rated for the load, and wire the operator with safety devices. The whole job usually runs $4,000 to $9,000 depending on width and automation. The quote is fixed before we start. Call (817) 241-4067 to have Hal walk the site with you.
Yes. For gates where trenching power from the house or building is impractical or expensive, we install solar kits from Ghost Controls and Mighty Mule with deep-cycle batteries and properly sized panels for North Texas sun. That said, a solar opener needs a healthy gate: clean swing, good hinges, balanced leaves. If your gate binds, the solar system will drain the battery and fail within weeks. We’ll check the gate’s mechanical condition before recommending solar. Call (817) 241-4067 for a free assessment.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Haltom City and the surrounding area since 2001.