Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Colleyville
Gate parts and welding in Colleyville usually comes down to one of three things: a hinge post that has moved, a welded joint that has cracked, or an operator that is straining against a gate it was never sized for. Our Gate Parts & Welding team handles all three, and we do the welding on site so your gate never leaves your property. If you live off Pleasant Run Road, Monticello, or anywhere along the Colleyville Boulevard corridor and your ornamental gate is sagging, binding, or dragging, call (817) 241-4067 and a live person answers. Hal Gatewood has been at this since 2001, and his name is on the shop and every invoice.
Why Gatewood Fence & Gate Is Colleyville’s Preferred Gate Parts & Welding Company
Here is what Colleyville homeowners tell us after they have already spent money with somebody else: the gate worked for a season, then the same sag came back. That is because a sagging gate is almost never fixed by adjusting hinges. It is fixed by addressing the post, the footing, and the weld. We have been called out to Colleyville estates in McPherson Ranch and the neighborhoods behind Covenant Christian Academy where the original hinge posts were set in shallow concrete on Blackland Prairie clay. Twenty years later, that clay has heaved and settled enough to pull the post out of plumb by an inch or more. If you only replace the hinge, you will replace it again in eighteen months. We pull the post, set a new one with deeper concrete, and weld hinges sized for the actual weight of the panel. The 90-Day Done Right Promise is in writing on every job. If it is not right, one call brings Hal back. No runaround, no third-party crew you have never met.
We also answer the phone. Around the clock, every day, a live person picks up. Not a voicemail tree, not a chatbot. The person who shows up for your Gate Installation - Colleyville is background-checked, uniformed, and works directly under Hal’s supervision. Call (817) 241-4067 for a free estimate with no trip charge inside the county.
Our Gate Parts & Welding Services in Colleyville
Hinge Replacement
On the ornamental iron gates common throughout Colleyville’s estate neighborhoods, hinges fail in two ways: the weld cracks from decades of freeze-thaw cycles, or the hinge pin wears egg-shaped and lets the panel drop. Either way, the panel starts dragging on the drive and the operator begins working twice as hard. We cut out the old hinge, grind the post clean, and weld in a new heavy-duty hinge sized for the actual panel weight. We do not reuse hardware that is past its service life to save a few dollars. That is how you end up calling the same company back every year.
Post Replacement
Post replacement is the most common structural weld call we handle in Colleyville. The Blackland Prairie expansive clay under this city swells with spring rain and shrinks through August drought, and over two or three decades that movement slowly walks a gate post out of square. A post that is off by just 1.5 inches makes a 600-lb ornamental panel bind against the operator. We excavate the old footing, set a new steel post in concrete deep enough to resist the heave, and weld the hinges back square. This is a two-person job with a welding rig in your driveway, and it is done right the first time.
Rail Repair
Rails crack and separate on Colleyville gates for the same reason hinges do: years of thermal expansion, ice storms, and the constant flexing of a heavy gate. When a lower rail separates from a picket, the gate loses structural integrity and starts to twist. We cut out the failed section, weld in a matched replacement, and grind the repair so it disappears into the original iron. On custom 1990s estate gates, we can match the scrollwork and picket profile so the repair is invisible.
Custom Welding
When a section of ornamental iron is too damaged to patch, or when a homeowner wants to modify an existing gate rather than replace it, custom welding is the answer. We have fabricated replacement sections, rebuilt gate frames, added steel stiffeners to panels that have begun to rack, and extended gates to close a gap. The advantage of working with a welder who is also a gate specialist is that the repair is built around the operator, the hinges, and the clearances, not just the broken part. Hal does the welding on site, and the work carries the same 90-Day Done Right Promise as everything we touch.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Colleyville
We are certified to service nine gate brands, including Linear, Viking, Ghost Controls, and Colleyville Doorking service. The part numbers change, but what matters for Colleyville is that we know which parts are in stock locally and which have to be ordered. We keep a rolling inventory of hinge sets, limit switch arms, photo eyes, and drive gears for the most common operator brands on the road. That means a typical repair in Colleyville does not have to wait on a warehouse three states away. Call (817) 241-4067 and ask for a free estimate, and mention the brand on your operator if you know it.
Common Gate Parts & Welding Problems We See in Colleyville Homes
- Hinge weld cracking from North Texas freeze-thaw cycles. A single ice storm can crack a 25-year-old weld that has already been stressed by the seasonal movement of Blackland Prairie clay. The crack usually shows up at the top hinge first, because that is where the panel pulls hardest.
- Motor drive gear stripping on undersized operators. Colleyville’s older estate gates were often built with an opener sized for a 300-lb panel. Then the homeowner upgraded to a 600-lb wrought-iron panel, and the motor has been straining ever since. By the time we get the call, the drive gear usually looks like a smooth washer.
- Post footing heave and settlement on the clay. Not all of Colleyville sits on identical soil, but the Blackland Prairie clay beneath most of the city moves more than people expect. A gate that was square in 1998 can be an inch and a half out of square in 2026, and no hinge adjustment fixes that.
- Gate rollers and track wear on slide gates. On multi-acre lots with long slide gates, the rollers wear flat spots and the track collects debris from landscaping crews. A bound-up roller makes the operator work harder, which shortens the life of the drive gear.
Pricing for Gate Parts & Welding in Colleyville, TX
Most gate parts and welding repairs in Colleyville run between $280 and $950 depending on the specific failure and the weight of the gate. A hinge replacement on a standard ornamental swing gate typically runs $280 to $450 including labor and new hinges. A full post replacement with new concrete and re-welded hinges runs $600 to $950 on most Colleyville lots. Custom welding and section fabrication is quoted per job after Hal sees the gate; small crack repairs start around $180. Drive gear replacement on a Linear or Viking operator typically runs $250 to $400. You get an exact price before any work starts, and that price does not change at the door. Call (817) 241-4067 for a free estimate. Seniors and veterans get a permanent 10% discount, and any repair over $200 is $40 off.
We Also Serve Cities Near Colleyville
We work up and down the Northeast Tarrant County corridor. Homeowners in Bedford, Hurst, North Richland Hills, and Keller call us for the same gate parts and welding work that we do in Colleyville, and we bring the same on-site welding rig and the same 90-Day Done Right Promise. If you are a few miles outside Colleyville, call (817) 241-4067 and ask if we can stop by.
Serving Colleyville, TX - Our Local Coverage Area
We’re based in the Colleyville area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Colleyville
Because the hinge post has likely shifted in the Blackland Prairie clay beneath your yard. Colleyville’s expansive soil swells with rain and shrinks in drought, and over 20 or 30 years that cycle walks the post out of plumb. Adjusting hinges on a moved post is a temporary fix. The permanent repair is post replacement and re-footing. Call (817) 241-4067 and Hal will come look at the post, not just the hinge.
Yes. Most of the ornamental gates built in Colleyville during the 1990s and early 2000s used standard picket profiles and scroll patterns that we can still source or fabricate. Hal welds in the replacement section, grinds the joint, and finishes the repair so it disappears into the original iron. Nobody wants a patch that looks like a patch on a custom estate gate. We do not do that kind of work.
Listen to the operator when it runs. A stripped drive gear whines, chatters, or slips under load, and the gate may move in jerks or stall halfway. If your Colleyville home has an original operator on a gate that was upgraded to a heavier ornamental panel, our Gate Motor & Opener in Colleyville team can tell you the gear has probably been degrading for years. We can pull the cover, inspect the gear, and tell you honestly whether it is worth saving or whether you are better off with a properly sized replacement. Call (817) 241-4067 for an honest look.
The repair depends on the crack location and the housing material. Most gate operator housings are cast aluminum or powder-coated steel, and a freeze-thaw crack can sometimes be welded, ground, and refinished. If the housing is too far gone, we replace it rather than patching a structural component. After any ice storm damage, we also check the limit switch arms and the photo eyes, because those are usually the next casualties. Estimates are free at (817) 241-4067.
Yes. On Colleyville estate gates, the hinge post is usually set separate from the masonry column, or the column is built around the post with enough clearance to work. We excavate carefully, set the new post, and do the welding without touching the brick or stone. If the column was built too tight around the old post, we will tell you before any work starts and talk through the least invasive approach. Call (817) 241-4067 and Hal will come out and look at your specific gate.
On-Site Welding for Colleyville’s Heavy Estate Gates
Colleyville is ranked among the wealthiest municipalities in Texas, and its residential build-out from the mid-1980s through the early 2000s left an unusually high concentration of ornamental iron automated driveway gates that are now 20 to 40 years old. The operators, hinges, and hardware on these gates are at end of life, and the homeowners who own them are not interested in cheap patches. They want the gate to run quietly, to stay square on the drive, and to last another 20 years. That is the kind of work we do. A tech who has worked Colleyville’s older estate neighborhoods for any length of time learns quickly that the original operators were often undersized for the panels homeowners later upgraded to. The opener was specced for a 300-lb gate, the new wrought-iron panel weighs 600 lbs, and the drive gear has been stripping for a decade before the first call comes in. Fixing that properly means addressing the whole system, not just the part that finally failed.
On a custom estate off Pleasant Run Road, our crew rebuilt a sagging ornamental iron swing gate after the original hinge post had heaved 2 inches out of alignment from the shifting Blackland Prairie clay. We excavated the old post footing, set a new steel post with deeper concrete, and welded new heavy-duty hinges so the 600-lb upgraded panel no longer drags on the drive. The owner’s LiftMaster operator now cycles smoothly, and we recalibrated the safety photocells before leaving. That is the difference between replacing a part and fixing a gate.
Drainage matters too. Colleyville’s clay soil holds water against buried post bases after heavy spring rains, and that trapped moisture accelerates corrosion on steel posts that were never sealed properly. We see it on gates that back up to the city’s creeks and low-lying lots near the Colleyville Nature Center. A post that looks solid at the surface can be paper-thin below grade. When we set a new post, we use concrete and sealant practices that stand up to this soil, not practices borrowed from a drier county.
Call Gatewood Fence & Gate for Gate Parts & Welding in Colleyville
If your gate is sagging, cracking, binding, or making noise it never used to make, call (817) 241-4067. You will reach a live person, not a voicemail. Hal Gatewood has been owner-operator since 2001, his name is on the shop, and he will give you a straight answer about what the repair costs and whether it is worth doing. Free estimates, no trip charge inside the county, and a written 90-Day Done Right Promise on every job. Serving Gate Parts & Welding in Colleyville and the surrounding communities.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Colleyville since the company opened its doors in 2001.