Linear Gate Parts & Welding Nationwide | Gatewood Fence & Gate

Linear Gate Parts & Welding in Fort Worth: What to Know First

We provide independent Linear gate parts and welding in Fort Worth, and most repairs are done the same day we arrive, with the gate staying in your driveway. A typical Linear hinge replacement or weld repair runs between $180 and $450 depending on what’s actually broken, and we quote the full price before any work starts. If a Linear gate is acting up, the problem is rarely the motor: it’s usually a hinge, a post, or a weld that let go. This page is for Fort Worth homeowners with a Linear gate that’s sagging, seized, or welded wrong by someone else. Call (817) 241-4067 and a live person answers.

Call (817) 241-4067

Key Takeaways:

• We’re an independent Linear service provider, not a manufacturer warranty line, so we fix rather than replace.
• Most Linear gate parts repairs in Fort Worth are done on-site the same day we come out.
• Price is quoted and agreed before any work starts, and it doesn’t change at the door.
• Every job carries the 90-Day Done Right Promise in writing.

How Linear Products Fail - and How We Fix Them

Linear builds solid openers and gates, but like every brand, they have their weak points, especially in North Texas where heat, clay soil, and wind do their own work. These are the failures we see most often on Linear setups across Fort Worth:

• Hinge failure on Linear SL and VS Series slide gates. The hinge plates are durable, but the bolts holding them to the post are the first thing to loosen in Fort Worth’s clay soils. The gate starts sagging at the corner, then the motor strains, then the mother board fries. We pull the sag out by resetting or replacing the hinge set, not by shimming the panel halfway.
• Bottom roller wear on Linear slide gate models. The roller brackets are cast aluminum and they grind down against the track over a few hot summers. You’ll hear a screech or a rattle before the gate refuses to move. We replace the roller with OEM Linear parts when they’re available, or a machined aftermarket roller that matches the original bolt pattern when they’re not.
• Weld cracks at the gate frame on Linear heavy-duty swing models. The Linear L series swing gates are sturdy, but a gusty Fort Worth spring can twist the frame just enough to crack a weld at the corner joint. Each time the gate cycles, that crack widens. We grind out the old weld, prep the steel, and weld it on-site so the gate never leaves your property.
• Post lean on any Linear gate installed in blackland clay. Fort Worth’s expanding clay doesn’t care what brand your gate is. A post set in a shallow or undersized concrete footer will lean, and the entire Linear system follows it. We cut, dig, re-set, and weld the post straight, then re-hang the gate so the opener isn’t fighting the geometry.
• Latch and lock misalignment on Linear pedestrian gates. This one’s simple but common: the latch bar or the strike plate shifts a quarter inch, and then people slam the gate harder, and then the whole frame twists. We realign the latch and lock, weld the strike plate in place where welding is the only durable fix, and send you on your way.

Our Linear Gate Parts & Welding Process

Here’s how a Linear repair goes from your first call to the gate working the way it should:

1. 1
   You call (817) 241-4067. A live person answers, not a voicemail. We ask a few questions about the Linear model and what the gate is doing, or not doing.
2. 2
   We schedule a time and show up. Hal Gatewood or one of his crew arrives in the window we promised, with a truck stocked for Linear work.
3. 3
   We diagnose on site. We find the actual failure point on the Linear unit before touching anything. That means checking the hinge posts, the rollers, the welds, and the opener travel.
4. 4
   We give you a written price. This is the full price for the repair, no hidden trip fee inside the county and no mystery add-ons at the end.
5. 5
   We weld or replace what’s broken. Welding happens right there in your driveway on most jobs. If a part needs replacing, we use OEM Linear parts when they’re the right call, or a quality aftermarket part that matches the spec and won’t void your system’s remaining coverage.
6. 6
   We test and clean up. We cycle the gate open and closed, check the stops and the safety sensors, and leave your driveway cleaner than we found it. Then we hand you the 90-Day Done Right Promise in writing.

What Linear Gate Parts & Welding Costs in Fort Worth

Here’s what you can expect to pay for Linear gate work in the Fort Worth area. These are honest ranges, not bait prices:

• Hinge replacement (single gate): $180 to $320, depending on the hinge type and how far the post has moved.
• Post reset and re-weld: $300 to $550 for a single post, including concrete and straightening.
• Weld repair, on site: $120 to $280 for most crack or break repairs, more if the frame is badly twisted.
• Roller replacement (slide gate): $140 to $260 per roller, including alignment.
• Latch and lock realignment: $95 to $180, welded if needed.

The biggest variable is the post. If the post is leaning, no part swap will fix it, and that’s where the price goes up. We’ll tell you straight up what it needs. Call (817) 241-4067 for a free estimate on your linear gate. We quote the full price before any work starts, and it doesn’t change at the door.

Why Fort Worth Homeowners Call Gatewood Fence & Gate for Linear Work

Hal Gatewood grew up on the south side of Fort Worth, not far from Hulen Mall, and he still lives about ten minutes from where he went to school. He learned welding and metalwork at Tarrant County College in the late ’90s, and since 2001 he’s been repairing gates all over Fort Worth. The name is on the shop, and the shop is down the road, that’s the oldest accountability there is. Every job carries the 90-Day Done Right Promise in writing. If it’s not done right, one call brings us back. We also service LiftMaster, Mighty Mule, Ghost Controls, and DoorKing, so if you’ve got more than one gate opener brand on the property we can handle it all without bringing in a second company. Give me a call, that’s my real number, and I’ll pick up.

FAQs

Call Gatewood Fence & Gate for Linear Gate Parts & Welding in Fort Worth

If you have a Linear gate that’s sagging, seizing, or welded together by somebody who didn’t know what they were doing, call (817) 241-4067. We’ll give you a straight answer, a written price, and a real person on the other end of the line, any hour of any day. We’ve been at this in Fort Worth since 2001, and the 90-Day Done Right Promise is stamped on every job we hand back. Free estimates, no trip charge inside the county, and a permanent 10% discount for seniors and veterans. That’s the whole offer, no haggling required.

Written by Hal Gatewood, Owner, Gatewood Fence & Gate at Gatewood Fence & Gate, serving Fort Worth and nearby areas.