BFT Gate Parts & Welding Nationwide | Gatewood Fence & Gate

BFT Gate Parts & Welding in Fort Worth: What to Know First

We provide independent BFT gate parts and on-site welding throughout Fort Worth, and most BFT hinge, post, and frame repairs are finished the same day we show up. The honest price posture is simple: we quote the job before we touch it, the number doesn’t change at the door, and you pay what we agreed on. If you own a BFT gate that’s sagging, dragging, or coming apart at a weld, call (817) 241-4067 and talk to a live person.

Call (817) 241-4067

This page is for BFT owners in Fort Worth who need straight answers about parts, welding, and whether a repair is worth doing. We’re an independent BFT service provider, not a factory warranty center, which means we can weld and rebuild what a manufacturer would tell you to replace.

How BFT Products Fail - and How We Fix Them

• BFT Deimos and Phobos swing gate hinges wallow out the post. We see this constantly in Fort Worth, especially on the older neighborhoods off Camp Bowie and in Wedgwood where gates have been swinging for 15 years. The hinge pin wears an oval into the bracket or the post, and the gate starts dragging on the latch side. The fix isn’t a new operator; it’s cutting out the worn hinge and welding in a fresh one, then re-hanging the gate so it closes square.
• BFT sliding gate rollers bind up and tear the track. The BFT rolling gate lines, like the Kustos, run on steel rollers that seize when dirt and limestone dust pack the bearings. Once a roller stops rolling, it slides, and then it grinds a flat spot into the bottom rail. We replace the roller with a sealed-bearing unit, check the track for wear, and weld-repair the rail if it’s still structurally sound.
• The gate frame itself cracks at the stress risers. BFT gates are built light and fast, but a Fort Worth summer with 100-degree heat followed by a cold snap will flex the frame enough to crack a weld at the corner gussets. On a BFT industrial or residential slide gate, the crack usually starts where the top rail meets the vertical stile. We weld the crack, add a gusset so it doesn’t come back, and grind it smooth so the gate looks like it was never touched.
• Latch alignment drifts, and the operator fights the gate. BFT swing gate operators are torque-sensitive. When the hinge post leans just a degree or two, the gate leaf shifts and the latch won’t line up, so the motor strains and eventually faults out. We pull the post back to plumb, weld the hinge mounts back true, and the operator stops working against itself.
• BFT underground operators let water into the foundation box. The BFT Hydra and similar underground swing operators sit in a steel box that can collect water if the drain holes clog with North Texas clay. What looks like an electrical problem is often a flooded box with rusted mounting bolts. We weld up a better bracket, re-set the operator, and clear the drains so it stays dry.

Our BFT Gate Parts & Welding Process

1. 1
   Call and talk to a person. You call (817) 241-4067, someone answers, and we talk through what the gate is doing. If it’s a BFT, we ask which operator you have and what the gate has been doing that it shouldn’t.
2. 2
   We show up and look at the actual gate. We don’t quote BFT work over the phone based on a brand name. We come out, put hands on the gate, and find out whether it’s a hinge, a weld, a roller, or something else. The diagnostic is free, and if we recommend work, you know the price before we pick up a tool.
3. 3
   Parts decision: OEM or better. If a BFT part is the right call, we use it. If an aftermarket part is equal or better and costs less, we tell you that too, because that’s what we’d want if it were our gate. We never swap a part that doesn’t need swapping.
4. 4
   The weld, the part, or both. Most of our BFT gate repairs are done in the driveway. We weld on site, so the gate never leaves your property. If it’s a hinge replacement or a post rebuild, the gate stays on our truck but the work happens right there.
5. 5
   Test it the way you use it. We cycle the gate a dozen times, check the limits, check the safety edges, and watch it close. If it’s not right, we’re not done.
6. 6
   Written guarantee. Every job leaves with the 90-Day Done Right Promise in writing. If something we touched isn’t right, one call and we’re back.

What BFT Gate Parts & Welding Costs in Fort Worth

BFT gate parts and welding in Fort Worth typically run:

• Hinge replacement, welded and re-hung: $220-$360 per hinge
• Gate frame crack repair with gusset: $180-$290
• Post replacement with on-site welding: $450-$800, depending on depth and re-concrete work
• Sliding gate roller replacement, including rail repair if needed: $190-$320 per roller
• Latch and lock rebuild or replacement: $140-$260
• Custom welding, per hour plus material: $95/hour, one-hour minimum

What moves the price: whether the post is rotted or just out of plumb, how thick the frame steel is, and whether the BFT operator itself needs to be re-set after the weld work. You’ll know the number before we start, and it won’t change when we’re done. Call (817) 241-4067 for a free estimate.

Why Fort Worth Homeowners Call Gatewood Fence & Gate for BFT Work

We’ve been fixing gates in Fort Worth since 2001, and we’re still owner-operated. Hal Gatewood’s name is on the shop and on every invoice. When you call, you talk to a live person, not a queue, and the person who shows up is background-checked, uniformed, and works for the company whose name is on the truck. We service BFT every week, and we’re also certified on LiftMaster, Mighty Mule, Ghost Controls, and DoorKing, so if your BFT operator is beyond saving, we can talk honestly about what to put in its place. Every BFT repair carries the 90-Day Done Right Promise, in writing, no fine print.

FAQs