Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterBFT Gate Access Control in Fort Worth: What to Know First
We repair and service BFT gate access control systems throughout Fort Worth. Most keypad, remote, and phone-entry jobs are diagnosed same-day and fixed within 24 to 48 hours. You’ll know the price before we turn a wrench, and it’s quoted in writing, not estimated over the phone and changed at the door.
This page is for Fort Worth homeowners and property owners who already have a BFT opener, keypad, or control board and want it working again or upgraded. If you’ve got a BFT model that another company said was a lost cause, give us a call at (817) 241-4067. We’re an independent BFT service provider. We fix what’s in your driveway, not what’s convenient for us to swap.
How BFT Products Fail - and How We Fix Them
- BFT Deimos and Phobos boards losing their limit settings. We see this constantly on Fort Worth homes with power fluctuations. A brownout or a nearby transformer surge wipes the board’s memory, and suddenly the gate won’t stop at the right point or reverses mid-cycle. The fix is usually reprogramming the limits and checking the power supply for voltage spikes. Some companies will sell you a new board at $600 plus labor for a problem that takes 20 minutes to resolve. We program it first, replace it only if it proves dead.
- Keypad failures on BFT Rigel and Icaro models. The wired keypads BFT used on these lines have membrane switches that wear out in Texas heat. The first symptom is numbers that work intermittently or not at all in hot weather. We’ve seen keypads that test perfectly inside a shop but fail when mounted on a sun-baked stone column in Tarrant County. If the pad is failing, we replace it with a weather-sealed aftermarket unit that holds up better than the original, or source the BFT part if you prefer factory. Completely up to you.
- Photocell misalignment triggering false obstructions. BFT systems use a through-beam photo eye at the gate opening, and Fort Worth’s clay soil shifts constantly. A post moves a quarter inch, the beam breaks, and the gate refuses to close or reverses for no visible reason. We align the cells, shim the mounting, and seal the wire connections against moisture. Half the BFT service calls we get billed as “bad board” by other companies turn out to be a photocell that simply needs aiming.
- Radio receiver drift on older BFT remote systems. The early rolling-code receivers BFT used, particularly on the E5 and T-Box lines, drift off frequency over a decade of hot attics and cold snaps. Owners report remotes that work from five feet but not from the street. The fix can be as simple as a receiver adjustment, or we install a new high-sensitivity receiver paired to your existing buttons if you’d rather not replace the remotes. We always try the adjustment first because a lot of these units still have years left in them.
- Capacitor failure on BFT single-phase motors. Homeowners hear a humming sound and the gate doesn’t move. That’s nearly always the start capacitor, a part that costs less than forty dollars and takes half an hour to replace. We see national outfits quote a full motor replacement for this. The motor wasn’t bad. The capacitor aged out. We replace the part, not the machine it was attached to.
Our BFT Gate Access Control Process
- 1
You call. A live person answers. Not a voicemail, not a menu. You tell us what the gate is doing or not doing, and Hal or his crew asks the right questions before anyone gets in a truck.
- 2
We diagnose on site. The person who shows up tests the board, the accessories, the wiring, the safety edges, and the motor with a multimeter. No guesswork emailed from a dispatcher. Real diagnosis in your driveway.
- 3
We show you what we found. If a part failed, we show you the part and explain why. If it’s a BFT board that can be reprogrammed instead of replaced, we say so plainly. Repairs are our first instinct, replacement our last.
- 4
Parts decision, your call. We source BFT factory parts when they’re available or high-quality aftermarket parts when they’re a better value or simply easier to get. Warranty requirements are explained up front. No sneaking in a knockoff part and charging OEM prices.
- 5
The fix happens on site. Most BFT access control work is done right in the driveway, including wiring repairs and component swaps. No hauling your gate off to some shop across town.
- 6
We test everything, then we test it again. Every keypad code, every remote, every safety edge and the auto-close function get cycled through at least three times before we pack up. Then you get the 90-Day Done Right Promise in writing. If it acts up, Hal comes back. No runaround.
What BFT Gate Access Control Costs in Fort Worth
Here are straight numbers for the BFT scenarios we handle most often around Fort Worth:
- Keypad replacement or reprogramming: $185 to $420
- Remote transmitter programming or new remote setup: $95 to $180
- Photocell alignment or replacement: $150 to $350
- Capacitor replacement: $120 to $250
- Starter relay or transformer replacement: $170 to $400
- Limit switch adjustment or repair (board-level fixes): $140 to $380
- Full BFT control board replacement: $450 to $900 depending on model and part availability
What moves the price: the specific BFT line you own, whether your existing wiring is sound or needs reworking, and whether the part is stocked locally or has to be ordered. Every price is quoted and agreed before work starts. That means no surprise invoices at the end. Call (817) 241-4067 for an exact number on your gate. Estimates are free.
Why Fort Worth Homeowners Call Gatewood Fence & Gate for BFT Work
Hal Gatewood has been fixing gates in Fort Worth since 2001. He grew up on the south side, not far from Hulen Mall, and he still lives about ten minutes from where he went to school. Tarrant County College in the late 90s is where he picked up welding and metalwork, and a broken driveway gate on a job in Wedgwood is what convinced him there weren’t enough people doing this work right. So he became the guy who does.
Every BFT job we touch carries the 90-Day Done Right Promise. If it’s not done right, Hal comes back and makes it right. No fine print, no conditions, no hedging. The name is on the shop, and the shop is down the road. That’s the oldest accountability there is.
We also know the BFT backup plan in Fort Worth. If your BFT opener is genuinely beyond economical repair, we service and install LiftMaster, Mighty Mule, Ghost Controls, and DoorKing systems too. We’ll tell you honestly whether your BFT has life left in it or whether you’d be better served by a different brand going forward. One call, straight answer.
FAQs
No, we’re an independent BFT service provider. That means we’re free to recommend the best fix for your situation, including aftermarket parts when they outperform BFT’s own, without worrying about a dealer agreement. We tell you all the options and let you choose. Authorized status matters less than someone who knows how the board actually behaves when a Texas summer hits it.
Most keypad, remote, and board issues are diagnosed and fixed within one visit. We carry common capacitors, relays, photo eyes, and receiver parts on the truck for exactly that reason. If your BFT board has to be ordered, the repair usually lands within 2 to 5 business days depending on stock. For urgent situations, call (817) 241-4067 and ask. A real person answers and will tell you the truth about the timeline, not just what you want to hear.
If your BFT product is still under manufacturer warranty, we’ll use BFT factory parts and follow the manufacturer’s service procedures so the warranty stays intact. If warranty isn’t a factor, we’ll present both OEM and aftermarket options with honest pricing differences. The decision is always yours, and the price note will show exactly what you’re paying for and why.
Depends on the unit, and we’ll tell you the truth. A bad capacitor, a drifted receiver, or a failing keypad is absolutely worth fixing. A mid-2000s BFT board with a fried main processor after repeated lightning strikes is usually not. The rule of thumb is simple: if the repair comes in under half the cost of a new opener and gives you at least three more years of reliable service, fix it. If it doesn’t, we’ll say so and show you honest replacement numbers instead. No pressure, no upsell.
Yes. Card readers, keypads, remotes, phone entry modules, video intercom panels, and any access control tie-in on a BFT system. If it opens a gate or talks to the gate, we work on it. A lot of the phone-entry systems on Fort Worth homes have their own control board in the house, and we test that too before we touch the gate, because a good half of phone-entry failures aren’t the gate opener at all. They’re the phone module. We find the real problem and fix that.
Get Your BFT System Working Right
If your BFT gate access control is acting up in Fort Worth, call Gatewood Fence & Gate at (817) 241-4067. A live person answers, day or night. We’ll ask a few questions, schedule a visit, and give you an honest price before any work starts. Give me a call - that’s my real number, and I’ll pick up.
Written by Hal Gatewood, Owner, Gatewood Fence & Gate at Gatewood Fence & Gate, serving Fort Worth and nearby areas.