Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Access Control Across Everman
Gate access control in Everman usually costs $180-$440 for Gate Repair - Everman, with full keypad or remote retrofit jobs running $650-$1,800 depending on the gate. We’re talking the difference between replacing a worn-out keypad face and re-engineering the post and hinge geometry on a 1960s pipe-frame gate that’s tilted two inches off plumb. Hal Gatewood has worked in southern Tarrant County for over two decades, and he’ll tell you straight: in Everman, the ground is almost always the culprit before the electronics are. Call (817) 241-4067 and a live person answers, day or night.
Why Gatewood Fence & Gate Is Everman’s Preferred Gate Access Control Company
Everman homeowners don’t have the option of tolerating a gate that half-works. A driveway gate that won’t open for the school bus at 6:45 a.m., or a keypad that works after rain but quits in August, isn’t a convenience problem. It’s a daily fight with your own property. Gatewood Fence & Gate is owner-operated, and Hal Gatewood’s name is on the shop and on every invoice. He’s been fixing gates since 2001, and when Everman customers call, they get a local person who knows Enon Avenue from Trammell Davis Road and who understands the clay under both.
We arrive in Everman in a clearly marked truck, with uniformed and background-checked people who carry parts for LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. You won’t get a call center. You won’t get a rotating cast. You’ll get a person who can show up, listen, look at the gate, and tell you what’s actually wrong before touching a screwdriver. And every job carries our 90-Day Done Right Promise in writing. If it isn’t right, one call brings us back. No runaround, no pro-rated excuses. That’s the whole promise, and it’s stamped on the paperwork.
Our Gate Access Control Services in Everman
Keypad Entry
A keypad entry system on an Everman gate has to survive heat, dust, and the occasional north-Texas ice event. We install and service keypads that are rated for outdoor exposure, hardwired or wireless, and we program them so you can set temporary codes for contractors or family without redoing the whole board. When an existing keypad starts misfiring on a 50-year-old welded pipe gate, we check the code pad, the wiring run, and the post alignment before we swap anything. Most keypad failures in Everman trace back to a post that’s moved, not a keypad that died.
Remote Control
Adding Gate Motor & Opener in Everman remote control to an older gate is usually straightforward, and it’s one of the least expensive upgrades we do. We match the receiver to your existing operator or install a standalone receiver if the old one’s fried. Then we program handheld remotes, teach you how to add or delete them, and show you the range limits for your specific property line. On several Everman lots, the driveway curves and fence lines sit close to FM 731, so we test remotes at the actual approach angle, not standing five feet away in the driveway.
Phone Entry
Phone entry systems let you open the gate from your cell, whether you’re at the kitchen window or across town. For Everman homes without a landline, we install cellular-based units that don’t depend on your home internet or old copper wiring. These systems are especially useful on rental properties and duplexes around the older streets near Everman High School, where multiple drivers need controlled access without sharing a keypad code with the whole street.
Card Reader
Card readers make sense when more than a few people need gate access, or when you want an audit trail of who came and went. We install proximity card readers, key fob systems, and readers that tie into the same control board as a keypad or phone entry. For Everman properties with employees, caretakers, or a constant stream of deliveries, a card system is often cheaper long-term than re-programming keypad codes every time a tenant changes. And if the gate itself is older, we’ll check the leaf balance and post plumb before mounting the reader bracket.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Everman
Gatewood Fence & Gate is certified to service nine major gate brands, including Viking, Ghost Controls, and DoorKing. We keep a deep stock of receiver boards, limit switches, photocells, and keypads for these brands on the truck, not on backorder. For Everman customers, that means we often fix the operator the same trip instead of scheduling a “parts run” and coming back next week. Hal has worked on DoorKing swing-arm units that are old enough to vote, and he knows which Ghost Controls boards fail from heat and which just need a relay cleaned. When a part does need replacing, we source it from local supply houses in Fort Worth, not a warehouse across the state. That’s how we keep turnaround short in Everman.
Our Gate Access Control team handles every brand and every age of gate. If you’re in Everman and the keypad’s dead, the remote won’t reach, or the gate closes a foot and reverses, call before you spend another weekend fighting it.
Common Gate Access Control Problems We See in Everman Homes
- Safety photocells that fault after heavy rain. The Blackland Prairie clay swells in spring, tilting the hinge post just enough that the photocell beam misses its reflector. The operator sees a “fault” and refuses to close. The fix is re-setting the post or shimming the photocell bracket, not replacing the board.
- Legacy boards that burn out relays. A 1980s or 1990s DoorKing or FAAC board cycling against a binding, sagging gate will cook relays until something gives. Usually the board. We repair or replace the board, then fix the gate geometry so the new one doesn’t die the same way.
- Loop detectors that lose sensitivity. Shallow driveway saw cuts from the 1950s and 60s shift with the clay, and suddenly the gate won’t open when you pull up to leave. We test the loop, re-set the sensitivity, and often re-cut a deeper loop bed so it stops happening.
- Keypads that work intermittently. Corrosion on the keypad ribbon cable or a cracked keypad face lets in rain and dust. We replace the keypad and seal the housing properly, then re-flash the codes if the old board lost its memory.
Pricing for Gate Access Control in Everman, TX
Here are real numbers for Everman, not vague ranges from a national pricing chart. A service call to diagnose an existing access control problem runs $75-$125, and we waive the trip charge inside Tarrant County when you approve the repair. Replacing a keypad face on an existing operator runs $180-$320. Adding remote control to an older swing gate runs $250-$480. A full keypad-plus-receiver retrofit on a 1960s or 1970s pipe gate, including post re-setting if the clay has moved it, runs $650-$1,800. The spread comes from the condition of the post and hinges, not from surprise charges at the end. Every price is written, quoted, and agreed before any work starts. Hal won’t hand you a higher invoice at the door. He’ll hand you the same number he gave you over the phone, plus the 90-Day Done Right Promise in writing.
Standing offers apply in Everman, no haggling needed: $40 off any repair over $200, no trip charge inside the county, free second opinions on any written estimate, and a permanent 10% discount for seniors and veterans. Our Gate Access Control work is quoted the same way every time: walk the gate, find the failure, price it in writing, then do the work.
We Also Serve Cities Near Everman
If you’re just outside Everman, we serve the surrounding Tarrant County communities with the same local response and the same written pricing: Fort Worth, Colleyville, North Richland Hills, and Hurst. The clay’s the same, the heat’s the same, and the fix for a tilted gate post doesn’t change at the county line. If your gate access control has quit and you’re inside the county, call (817) 241-4067 and ask for Hal.
Serving Everman, TX - Our Local Coverage Area
We’re based in the Everman area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Access Control in Everman
Because the clay under your gate post is doing the failing, not the electronics. Everman sits on Blackland Prairie clay that swells when wet and shrinks when dry. After a wet spring, the post tilts enough that safety photocells misalign and the operator faults. In a dry summer, the clay shrinks, the post leans the other way, and the gate binds. The electronics are often fine. The fix starts with checking post plumb and re-setting the footing if the movement is more than a half inch. Call (817) 241-4067 and we’ll diagnose it at the gate, not over the phone.
Almost always yes, and in Everman that’s usually the right call. Those custom-welded pipe gates from the 1960s and 70s were built to non-standard widths, so a prefabricated replacement panel won’t match the opening anyway. We fabricate and weld a keypad mounting plate onto the existing gate as part of our Everman Gate Installation service, run the low-voltage wiring, and tie the keypad into either a new or existing operator. If the post has heaved, we re-set the post first. The original gate stays in your driveway. It’s cheaper than replacing a gate that was built better than most of what you can buy now.
On an old slide gate in Everman, the ground is the first suspect. Clay shrink-swell moves slide-gate track supports and shifts the leaf enough that the photocell beam misses its reflector. The board then reads a “fault” and reverses or refuses to close. We test the photocells directly, check the beam alignment, and then check the track level. If the board is the actual failure, we repair or replace it. But in Everman, the board is usually the victim, not the villain. Your best move is to call (817) 241-4067 and let us put eyes on the gate before you buy a new board.
Because the driveway saw cut holding the loop wire was probably cut shallow in the 1950s or 60s, and the clay has shifted or crusted the wire over the decades. The loop detector is still working, but it can’t “see” your vehicle because the wire’s signal has degraded or the loop bed has moved. We test the loop with an inductance meter, and often the fix is re-cutting a deeper loop bed and installing fresh wire, not replacing the detector. On a 1970s Everman driveway, this is a common repair, and it’s one that bigger companies often misquote as a “board replacement.”
Yes, if the gate is re-hung and the post is stabilized at the same time, and no, if you only bolt on a receiver and call it done. A 1970s swing gate in Everman sags because the hinge post moves with the clay, not because the gate is “old.” We re-set the post, re-hang the gate so the leaf is balanced, and only then install the remote receiver and program the remotes. If you skip the post work, the new receiver will just operate a gate that still fights itself, and the operator will burn out again. Done right, a retrofitted remote on an old Everman gate works for years. Done wrong, you’ve spent money twice.
Call Gatewood Fence & Gate for Gate Access Control in Everman
If you’re in Everman and the gate won’t open, the keypad’s dead, or the photocell light blinks at you every time you try to leave for work, call (817) 241-4067. Hal Gatewood has been fixing gates in Tarrant County since 2001, and he answers the phone like a neighbor, not a script. We’ll schedule a time to meet you at the gate, walk the ground with you, and give you a written price before any work starts. Free estimates, no trip charge inside the county, and the 90-Day Done Right Promise on every job. The name’s on the shop, and the shop is down the road. That’s still the oldest accountability there is.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Everman since 2001.