Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Access Control Across Benbrook
Gate access control in Benbrook, TX typically runs $220-$480 for a new weather-sealed keypad entry system installed, and $350-$900 for a video intercom or smart access retrofit on an existing operator. We do this work in Benbrook nearly every week, and we know what the lake humidity does to circuit boards before we even pull the cover off. Hal Gatewood has been fixing and retrofitting gates since 2001, and the name is on the shop, not on a call center three states away. When your keypad stops reading codes off Winscott Road or your card reader quits on a cove-side street, call (817) 241-4067 and a live person answers, day or night.
Why Gatewood Fence & Gate Is Benbrook’s Preferred Gate Access Control Company
We have worked on more gate access control systems in Benbrook than most outfits will see in a decade. The lake-adjacent properties along Winscott Road, the older ranch homes near I-20, the newer iron gates in south Benbrook off FM 2871 – we know the streets, the soil, and the specific ways operators fail here. Hal shows up himself or sends someone from his crew who has been doing this long enough to spot a corrosion problem before it strands you outside your own driveway.
Benbrook customers call us because we answer the phone with a person, not a recording. Every job carries the 90-Day Done Right Promise in writing. If it is not done right, one call brings Hal back. No runaround, no “that is a different department” nonsense. We are locally owned, owner-operated, and the address is published so you can drive over and look Hal in the eye if you want to. That is the oldest accountability there is.
Our Gate Access Control Services in Benbrook
Keypad Entry
Keypad entry systems in Benbrook face a specific enemy: morning fog off Benbrook Lake. Condensation settles inside the enclosure, shorts the keypad membrane, and suddenly your code works when it feels like it. We install weather-sealed keypads with conformal-coated circuit boards and add dielectric grease to every harness connection. For homes on cove-side streets, this is not an upsell. It is the difference between a keypad that lasts four years and one that lasts twelve. A typical keypad entry replacement or new installation in Benbrook runs $220-$480, depending on whether you need a standalone unit or full operator integration.
Video Intercom
Video intercom systems for Benbrook driveways give you eyes on the gate from inside the house or from your phone. We retrofit video intercoms onto existing operators from LiftMaster, DoorKing, Viking, and others, and we wire them so the camera actually triggers when someone pushes the button – not ten seconds later. For Benbrook homes with long setbacks and driveway gates you cannot see from the front window, a video intercom is the smartest access upgrade we recommend. Budget $350-$900 for a retrofit, depending on the operator and whether you need wifi bridging to the house.
Phone Entry
Phone entry systems let a visitor call your cell from the gate, you press a button, and the gate opens. For Benbrook homeowners who get deliveries or have contractors coming and going, it is simpler than handing out codes. We install phone entry units on both slide and swing gates, and we tie them into the existing operator without replacing what still works. The catch on older Benbrook operators is the relay board – if it is original to a 1980s or 1990s ranch home, we usually replace it before adding phone entry, because the old relay will not handle the load. Phone entry installation in Benbrook typically runs $300-$650.
Card Reader
Card reader access on Benbrook gates fails in a way we do not see inland. The gate post shifts with the Vertisol clay, the reader gap widens, and suddenly tags stop reading even though the reader itself is fine. We correct the post footing first, then address the reader. On lake-adjacent properties, we also seal the reader housing against humidity ingress and use stainless mounting hardware. A card reader install or replacement in Benbrook runs $280-$550, including post alignment where needed.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Benbrook
We service and retrofit access control on Linear, Viking, DoorKing, LiftMaster, FAAC, BFT, and Mighty Mule systems, among others. We keep common Gate Access Control parts stocked so Benbrook jobs do not stall waiting on a shipment. If you have an older Viking keypad off Winscott Road or a DoorKing operator in south Benbrook, we can usually diagnose it on the first visit and fix it the same day. If the part is exotic, we tell you honestly what it costs and when it will land.
Common Gate Access Control Problems We See in Benbrook Homes
- Keypads that work intermittently near the lake. Morning fog off Benbrook Lake condenses inside the keypad enclosure and shorts the membrane. We see this on cove-side streets routinely, and the fix is a weather-sealed replacement, not repeated code resets.
- Legacy operators with no entrapment protection. Many 1970s to 1990s ranch homes in Benbrook still run their original gate operator without photocells or safety edges. That is a liability and an injury risk. We replace the control board rather than patching around it.
- Card readers or phone entry units that stop reading tags. Shifting hinge posts from Vertisol clay heave move the reader out of alignment, and tags fail. We fix the post footing before touching the electronics, or you will fix it twice.
- Rust on galvanized steel gate frames and hardware. The humidity off Benbrook Lake surface-rusts galvanized frames within a few years. We see homeowners genuinely surprised that their “rust-resistant” gate is pitting. Powder-coated or aluminum retrofits are a conversation we have more often in Benbrook than anywhere else in the Fort Worth metro.
Pricing for Gate Access Control in Benbrook, TX
Here is what Benbrook homeowners should budget. Keypad entry: $220-$480. Card reader: $280-$550. Phone entry: $300-$650. Video intercom retrofit: $350-$900. Smart access conversion on an existing operator: $400-$950. Control board replacement on a legacy operator: $300-$700. The price is quoted and agreed before any work begins, in writing, and we do not show up with a different number. Estimates are free. We offer $40 off any repair over $200, no trip charge inside the county, a free second opinion on any written estimate you already hold, and a permanent 10% discount for seniors and veterans. Call (817) 241-4067 for an exact quote.
We Also Serve Cities Near Benbrook
Our crew works Benbrook every week, and we cover the surrounding area too. If you are in Benbrook, Fort Worth, Colleyville, North Richland Hills, or Hurst, the same live-answer phone line and the same 90-Day Done Right Promise applies. The shop is a short drive from any of these, which means parts and people move fast when your gate will not.
Serving Benbrook, TX - Our Local Coverage Area
We’re based in the Benbrook area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Access Control in Benbrook
Morning fog off Benbrook Lake condenses inside the keypad enclosure, shorting the membrane and causing intermittent codes. The fix is a weather-sealed keypad with a conformal-coated board and dielectric grease on the connections. We do this repair on cove-side streets off Winscott Road regularly. Call (817) 241-4067 for a free estimate.
In most cases, we replace the control board to add modern entrapment protection rather than the whole operator. If the motor and gearbox are sound, a board replacement typically runs $300-$700 and brings the operator up to current safety standards. If the operator is original to a 1980s ranch home, replacement is usually the cheaper long-term answer because the old board is obsolete and a new operator includes a warranty. We will quote both and let you decide. Call (817) 241-4067.
Benbrook’s Vertisol clay soil heaves after rain, tilting the gate track or posts and binding the gate, which trips the operator’s obstruction sensor. The fix is correcting the post footing and track alignment before touching the electronics. This is the single most common gate problem we see in Benbrook after a wet week. Call (817) 241-4067 for a free estimate.
Yes, we retrofit smart access systems to older DoorKing operators regularly in south Benbrook. We add a smart controller that lets you open the gate from your phone and assign temporary codes for deliveries, and we tie it into the existing operator without replacing what still works. A typical smart access retrofit runs $400-$950. Call (817) 241-4067.
Yes. The persistent humidity and fog off Benbrook Lake surface-rusts galvanized steel gate frames within a few years, even if the manufacturer said “rust-resistant.” We see this on lake-adjacent properties constantly. The long-term fix is a powder-coated or aluminum retrofit, which is an easier conversation in Benbrook than anywhere else in the Fort Worth metro. Call (817) 241-4067 for an honest assessment.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Benbrook, TX.
If your gate will not open, your keypad is dead, or you want a smart access system that actually works in lake humidity, call (817) 241-4067. A live person answers. The estimate is free, the price is set before work begins, and the 90-Day Done Right Promise is in writing. Hal’s name is on the shop – and the shop is down the road.