Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterMighty Mule Gate Parts & Welding in Fort Worth: What to Know First
We repair Mighty Mule gate openers and weld gate frames in Fort Worth, TX - typically same-week for parts we carry, and most hinge, post, and frame repairs are done in one trip. You’ll know the price before we start, and it won’t change at the door. If you own a Mighty Mule that’s grinding, sagging, or quit responding, call us at (817) 241-4067 and we’ll tell you straight whether it’s a part worth replacing or a weld worth making.
This page is for Mighty Mule owners in Fort Worth who need honest answers about gate parts and welding. We are an independent Mighty Mule service provider - not affiliated with the manufacturer, and not interested in selling you a whole new system when a $40 bracket and a good weld will do. But we’ll also tell you when a repair is throwing good money after bad, and Hal will say so plainly either way.
How Mighty Mule Products Fail - and How We Fix Them
Every gate brand fails in its own way. Here’s what we see on Mighty Mule systems in Fort Worth, and what we do about it.
- FM-series hinge bracket welds cracking at the post. The FM200 and FM500 mount their opener arm to a steel bracket that often gets welded to the gate frame by whoever installed it. In Fort Worth, our freeze-thaw cycles plus the constant tugging from the opener eventually crack those bracket welds. We cut out the old weld, re-weld with proper penetration, and add a gusset where the bracket allows it. You’d be surprised how many “dead openers” are just a bracket that came loose.
- MM-series actuator mounts tearing loose from thin-walled gate frames. The MM260 and MM360 are common on Tarrant County residential gates, and the actuator post brackets love to wallow out or tear away from lighter 16-gauge tube. We plate the frame at the mount point, weld on a heavier base, and re-anchor the bracket before the opener arm ever goes back on. Fix the mount without reinforcing the frame and you’ll fix it twice.
- Gate sag causing the opener to bind mid-travel. A Mighty Mule opener doesn’t sag - the gate does. When a hinge post leans or hinge barrels wear, the gate drops enough that the opener arm binds, strips the screw drive, or throws a limit-code error. We reset the post in fresh concrete, replace worn hinges, and re-weld the hinge pin seats. Then the opener runs quiet again. Show me the gate closing on its own and I’ll show you where it’s failing.
- Photo-eye and limit switch brackets getting knocked out of alignment. Mighty Mule photo-eyes and magnetic limit switches get mounted on little slip brackets that vibrate loose. We don’t just re-tighten them - we weld small anchor tabs or reposition the brackets so they hold alignment for years, not months. A gate that reverses for “no reason” is usually an eye that’s moved a half inch.
- Aftermarket hinge and roller parts wearing out in a single season. We see plenty of Mighty Mule gates swinging on box-store hinges that weren’t meant for the load. The Mighty Mule line is fine - the hardware some installers hang it with is not. We use heavy-gauge hinges and sealed bearing rollers sized to the gate weight, and we weld them so they don’t shift.
Our Mighty Mule Gate Parts & Welding Process
Here’s how a typical Mighty Mule repair goes from your phone call to the gate working right.
- 1
You call (817) 241-4067. A live person answers, day or night. We ask what the opener’s doing, what model it is, and whether the gate has been hit or sagging. That gives us a good idea of what to load in the truck.
- 2
We show up and diagnose in front of you. Hal or one of his crew checks the opener, the mount, the hinges, the post, and the battery. We point to what failed and explain it in plain English.
- 3
We write the price and get your go-ahead. The number we quote is the number on the invoice. If we find a second issue, we stop and talk to you before touching it. Free estimates, and no trip charge inside the county.
- 4
We repair, reinforcing as we go. If it’s a bracket, we weld it. If it’s a hinge, we replace it. If it’s a post, we re-set it. If a part is shot, we offer OEM or a quality aftermarket option that fits your budget - and we tell you honestly which one makes sense for your gate.
- 5
We test the full cycle with obstruction stops and voltage checks. The gate has to close gently on the stop, reverse on the eye, and hold alignment. We run it several times before we leave.
- 6
The 90-Day Done Right Promise goes on paper. If it’s not done right, we make it right. One call brings us back - no runaround.
What Mighty Mule Gate Parts & Welding Costs in Fort Worth
Here’s what we typically see on Mighty Mule jobs in Fort Worth. These are honest ranges, not bait numbers.
| Repair/Service | Typical Range |
|---|---|
| Hinge replacement (pair, welded on-site) | $180 - $320 |
| Hinge post straighten or re-set in concrete | $200 - $450 |
| Gate frame crack repair (weld, gusset, grind) | $150 - $350 |
| Opener bracket re-weld and reinforce | $120 - $250 |
| Gate roller replacement (pair, heavy-duty) | $140 - $260 |
| Latch or lock alignment and repair | $90 - $180 |
| Full Mighty Mule opener swap (carry-over existing mounts) | $350 - $600 |
What moves the price: gate weight, access to the post, how much concrete work is involved, and whether we’re dealing with rust or damage from a previous “repair.” You always know the price before the first weld or bolt comes loose. Call (817) 241-4067 for a free, written estimate on your specific gate.
Why Fort Worth Homeowners Call Gatewood Fence & Gate for Mighty Mule Work
The name on the shop is the name on the side of the truck. Hal Gatewood grew up on the south side of Fort Worth, learned to weld at Tarrant County College in the late ’90s, and has been fixing gates here since 2001. He’s not passing through. The address is published, the license is checkable, and if you want to look him in the eye before he starts, you can drive to the shop.
Every job carries the 90-Day Done Right Promise in writing, not in fine print. Calls are answered by a live person around the clock. The person who shows up is the same person you’ll see at the hardware store. And because we service Mighty Mule every week - alongside LiftMaster, Ghost Controls, and DoorKing - we know how your Mighty Mule should run and how it shouldn’t. If the gate is mangled, we’ll say so. If the fix is simple, we’ll say that too. That’s how we’ve stayed in business over 29 years.
Frequently Asked Questions
Yes - most FM-series actuators, control boards, remote programmers, and mount brackets are still available, though some older board revisions have long lead times. We keep common wear items on the truck and can usually have less common parts in hand within three to five business days. Call (817) 241-4067 with your model number and we’ll tell you exactly what’s available and what it’ll cost.
Regular repairs, hinge replacement, bracket welding, and using third-party structural parts do not void your Mighty Mule warranty on the opener itself. The warranty covers manufacturer defects in the opener, not the gate hardware it attaches to. Welding on the gate frame is outside the opener warranty entirely. We’re an independent Mighty Mule service provider, so we don’t route through the manufacturer for parts - but we always work warranty-safe on the opener side.
If the control board is good and the gearbox isn’t grinding, repair is almost always the better route. Aktuator arms, mounts, hinges, and limit brackets are cheap compared to a full replacement. If the board is cooked and the actuator is worn out, we’ll tell you straight and give you a hard number for replacement. Hal would rather fix your gate than sell you an opener you don’t need.
We do almost all Mighty Mule gate welding on-site with a mobile rig - the gate stays in your driveway, and you can watch the work happen. We only haul a gate off in the rare case it’s so badly wrecked it needs a jig in the shop. On-site welding means less downtime and no “shop fee” padded into the bill.
For a gate that won’t open or close securely, we make it out fast - often same-day, depending on where you are in the county and what’s already on the schedule. Calls are answered by a live person, not a messaging service, so you’ll know the window before you hang up. Give me a call - that’s my real number, and I’ll pick up: (817) 241-4067.
Call Gatewood Fence & Gate for Mighty Mule Parts & Welding in Fort Worth
If your Mighty Mule gate is sagging, grinding, or swinging loose in Fort Worth - or anywhere nearby in Tarrant County - call us. We’ll show up when we say we will, tell you what’s actually wrong, and give you a written price before any work starts. Free estimates. No trip charge inside the county. And if it’s not done right within 90 days, we come back and make it right. Call (817) 241-4067 now and talk to a real person.
Written by Hal Gatewood, Owner, Gatewood Fence & Gate at Gatewood Fence & Gate, serving Fort Worth and nearby areas.