Mighty Mule Gate Motor & Opener Nationwide | Gatewood Fence & Gate

Mighty Mule Gate Motor & Opener in Fort Worth: What to Know First

We repair and install Mighty Mule gate motors and openers across Fort Worth as an independent Mighty Mule service provider, typically arriving same day or next day for a motor that won’t budge. Most Mighty Mule repair jobs in the Fort Worth area run between $180 and $340, and we quote the exact price before any work starts, in writing, so there are no surprises at the door. If you own a Mighty Mule gate opener that has suddenly quit, is grinding, or won’t hold its limit, this page tells you what is actually going wrong and how we fix it. Call (817) 241-4067 for a free estimate.

Call (817) 241-4067

How Mighty Mule Products Fail, and How We Fix Them

Mighty Mule makes a solid gate opener for the money. But after 29 years of working on these units in Fort Worth driveways, we know exactly where they break and why. Here is what we see most, by model line.

• MM371W and MM372W swing arm motors: The plastic worm gear inside the gearbox strips, usually from a gate that was slightly too heavy or hinges that let the gate drag on the ground. The motor still hums, but the arm won’t move. We replace the gear with an aftermarket brass or steel version when available, because the OEM nylon gear will strip the same way again inside a year. If the arm itself is bent from a wind gust, we straighten or replace it and set the force limit correctly so it does not happen twice.
• FM200 and FM350 solar/battery models: The 12V battery goes bad every two to three years in Texas heat, and the control board’s transformer starts clicking instead of charging. We see this constantly in Fort Worth subdivisions like Watersbend and Park Glen, where gates bake in the afternoon sun. The fix is a fresh deep-cycle battery, a board check, and usually a solar panel angle adjustment so the battery actually charges during the short winter days.
• RB741 and RB842 slide gate motors: The limit switch magnets fall off the rail or get knocked loose, which makes the gate overtravel and slam into the end stop. That slamming is what destroys limit switches and bends brackets. We reset the limits, replace the magnets with properly torqued hardware, and verify the gate coasts to a soft stop at both ends.
• MM560 and MM562 heavy-duty swing units: The torque limiter on the arm starts slipping, usually after someone hit the gate with a vehicle or a tree branch hung the travel. The gate opens partway, then stalls. We replace the clutch disc, adjust the arm geometry, and correct the gate’s weight balance by fixing the hinge post, not just cranking the opener harder.
• The “worked fine yesterday” call: On nearly every Mighty Mule model we see, lightning or power surges in Fort Worth’s summer storm season take out the transformer or the control board on wired units. If the unit was plugged into a regular outlet without a surge protector, that is usually the story. We replace the damaged transformer or board and add a proper surge suppressor so the next storm does not repeat the job.

Our Mighty Mule Gate Motor & Opener Process

Here is what a Mighty Mule service call with us actually looks like, from the moment you call to the moment the gate runs right.

1. 1
   Call and talk to a person. You call (817) 241-4067. A live person answers, day or night, and schedules a time window. We tell you upfront that the trip charge is waived inside the county.
2. 2
   We show up and diagnose. We check the motor, the arms, the control board, the battery or transformer, and the gate itself. We test the gate’s balance and travel before we ever blame the opener, because a fine opener on a sagging gate will fail in months no matter what.
3. 3
   We give you a written price. Before anything gets taken apart, we quote the exact repair, parts included. You approve it or you don’t. No pressure, no “while we’re here” upsell.
4. 4
   We fix it in your driveway. On a Mighty Mule job, we replace what is broken with OEM parts where it matters for warranty, and better-than-OEM aftermarket parts where the original design is the weak link. The gate stays in your driveway; the welding and motor work happen on site.
5. 5
   We test it five times. We run the gate through full open and close cycles at least five times, check the auto-reverse and safety edges if equipped, and set the force limits so a child or a dog does not get pinched.
6. 6
   We write the 90-Day Done Right Promise on the invoice. If it acts up within 90 days, call. Hal comes back and makes it right. That is the whole promise, not the short version.

What Mighty Mule Gate Motor & Opener Costs in Fort Worth

If your Mighty Mule opener has failed, here is what you can expect to pay in the Fort Worth area, in honest dollars.

• Service call and diagnosis: $89 to $125 if outside the free-trip area, and we credit that toward the repair if you proceed.
• Battery replacement on FM200/FM350: $120 to $190 depending on battery capacity.
• Worm gear replacement on MM371W/MM372W: $180 to $280 including labor.
• Control board or transformer replacement: $220 to $340, depending on model and surge damage.
• Full motor replacement on a slide unit (RB741/RB842): $450 to $750 installed, depending on gate weight and travel length.

What moves the price is mostly parts availability and whether the gate itself needs hinge or track work. We quote it all upfront before the first tool comes off the truck, and the price on the invoice matches the price we quoted. Call (817) 241-4067 for a free, no-obligation estimate on your Mighty Mule opener.

Why Fort Worth Homeowners Call Gatewood Fence & Gate for Mighty Mule Work

Hal Gatewood has been fixing gates in Fort Worth since 2001, and he grew up on the south side near Hulen Mall, so when he says he will be there Tuesday, he means Tuesday. Our shop address is published, our phone is answered by a real person 24/7, and the 90-Day Done Right Promise is stamped on every invoice, not buried in fine print. We service all nine major gate brands, so if your Mighty Mule opener is beyond saving and a LiftMaster or Ghost Controls or DoorKing unit makes more sense, we can tell you that straight and install it without pushing something you don’t need. That is the difference between a company that wants to sell you a part and a guy who wants the gate to close right for the next decade.

FAQs