Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFAAC Gate Access Control in Fort Worth: What to Know First
FAAC gate access control in Fort Worth typically breaks down into two jobs: the operator itself has failed, or the keypad, receiver, or phone entry module feeding it has died. We handle both. An access control call usually gets a living person on the phone at (817) 241-4067 the first time, and most FAAC issues we see are diagnosed same-day and fixed within one to three days once parts are in hand.
This page is for FAAC owners in Tarrant County and the surrounding area who want straight answers on what their system costs to repair, which parts are worth replacing, and whether a failing gate access system means a whole new operator. Hal Gatewood has been fixing these systems in Fort Worth driveways since 2001, and he’s seen enough FAAC failures to know exactly where to look.
How FAAC Products Fail - and How We Fix Them
- FAAC 750 and 750D operators losing radio range. Homeowners in Fort Worth’s older neighborhoods like Ridglea, Wedgwood, and the western edges of Crowley are running FAAC 750 series operators that are now ten-plus years old. The symptom is always the same: the remote works from 30 feet away but not from the street. Nine times out of ten the problem isn’t the remote’s battery or the motor. It’s the receiver antenna connection that has corroded inside the cabinet, a failure we see twice as often after wet winters and the humidity swings Fort Worth gets every spring. We replace the antenna lead, clean the receiver board contacts, and in many cases the original remote works again without reprogramming.
- FAAC 400 and 402 operators losing their open/close memory. The FAAC 400 series is common on smaller residential swing gates in the exurbs southwest of Fort Worth. The board’s EEPROM can fail gradually, especially if the unit lives in full sun without a canopy. Homeowners describe the gate “forgetting” its limits, slamming open, then reversing halfway. The fix is usually a new control board, not a new operator. We warn owners here: an OEM FAAC board for a 400 series often runs close to what the operator originally cost, so we will quote both the board replacement and a comparable whole-operator replacement, and let you make the call with the numbers in front of you.
- FAAC 770 hydraulic gate operators and access control integration. The 770 is a heavier-duty hydraulic unit we see on gated properties in the hills northwest of Fort Worth, where drives are long and gates are heavy steel. The frustration with access control on these is that the keypad and phone entry add-on modules are from a different generation of FAAC engineering than the operator itself. The wiring at the terminal block is finicky, and a loose landing on the logic connection will take down the whole input side while the motor still runs fine by remote. We solder the terminal connection rather than retightening it. That is not a warranty-safe disclaimer; it’s just the only repair that holds on those units.
- FAAC 844 Erreka and Mini Smart keypad panels failing after storms. Flood-style storms that roll through Fort Worth in April and May are hard on surface-mounted keypad panels. The FAAC Mini Smart and 844 keypads use ribbon and board connections that absorb moisture, and after one hard rainy season you get ghost entries, double-digit presses, or full dead displays. We replace the panel internals with a sealed aftermarket equivalent that fits the existing enclosure, which keeps the repair under half the price of a full FAAC panel replacement. It also keeps the wiring and hinge work original, which matters if the gate arm itself is still in good shape.
- FAAC swing gate “juddering” caused by the gate’s own hinge posts, not the access control. This is the Hal Gatewood class of repair, and it comes up so often on FAAC properties across Fort Worth that it belongs on this list even though it’s not strictly an access control part. A gate jerks and then reverses mid-cycle, and the owner assumes the opener or board is failing. We find the real fault is a sagging hinge post, often from a prior fence install that should never have carried a powered gate. We weld reinforcement and reset the gate before we touch the operator. Replace the board and leave the post sagging, and you’ll be calling someone else back in six months.
Our FAAC Gate Access Control Process
- 1
You call (817) 241-4067. A live person answers immediately, twenty-four hours a day. We are not a call center, and you won’t sit on hold while a phone rings in another state.
- 2
We visit the gate in Fort Worth and diagnose the whole path. Access control failure is rarely the first component that looks broken. Hal or one of his background-checked crew checks the power supply, the board, the inputs, and the operator itself before quoting anything.
- 3
You get an exact price, on paper, before any work starts. Every quote is agreed to before we turn a single screw. No surprise line items, no “we found another issue once we opened it up” games.
- 4
We repair what is broken and weld what needs welding. On a FAAC job, that often means reterminating a logic line, soldering a loose connection, replacing a receiver board, or reinforcing a hinge post. If a part needs replacing, we tell you the straight difference between an OEM FAAC part and a quality aftermarket option, including price and expected lifespan.
- 5
We test the full access control sequence repeatedly. Keypad code in, remote open, safety reverse, limit stop. Not once, until it works. Three or four cycles at minimum.
- 6
We leave the site clean and hand you the 90-Day Done Right Promise in writing. If anything related to our repair does not hold, you call back and Hal comes back. No phone tree, no arguing. It’s his name on the invoice.
What FAAC Gate Access Control Costs in Fort Worth
No one should have to call a contractor blind, so here is what FAAC access control work actually costs in the Fort Worth market:
- $220-$380 - Standard receiver board replacement on a FAAC 400 or 750 series, including the part, on-site labor, and a full function test.
- $300-$520 - Full keypad panel swap (sealed aftermarket panel fitted to existing enclosure) versus $600-$900 for a new FAAC OEM panel.
- $260-$450 - Access loop detector replacement or repair on a FAAC swing gate, including digging the new loop where install is straightforward.
- $500-$1,200 - Complete access control board replacement plus retermination and soldering of the input side, when the operator itself is still sound.
- $1,500-$2,800 - Full replacement of a FAAC 750D or similar operator when the unit has racked up 12-plus years and the motor, gearbox, and board are all at end of life.
What moves the price is mostly the age of the unit and whether the hinge posts were installed strong enough to carry a powered gate in the first place. If the post is solid and the operator is clean, repairs stay small. Call (817) 241-4067 and describe what you’re seeing. Estimates are free, and we won’t quote you a number over the phone that changes when we show up.
Why Fort Worth Homeowners Call Gatewood Fence & Gate for FAAC Work
Hal Gatewood grew up on the south side of Fort Worth, not far from Hulen Mall, and he’s been fooling with gates and welders since Tarrant County College in the late ’90s. His name is on the shop, his address is published, and he still lives ten minutes from where he went to school. When you hire Gatewood Fence & Gate, you’re not hiring a franchise with a rotating cast of subcontractors; you’re hiring the guy who answers the phone and stands behind a 90-day written guarantee. If it’s not done right, we make it right. One call brings Hal back to the driveway.
We are also not a one-brand shop. Hal and his crew service LiftMaster, Mighty Mule, Ghost Controls, and DoorKing alongside FAAC, which matters when you have a mixed-property setup like a LiftMaster front gate and an older FAAC rear gate, and you want one person who can diagnose both without pointing fingers at another company. And if the repair is simpler than you feared, we say so, out loud, before we touch anything.
FAQs
Every FAAC repair we do carries our 90-Day Done Right Promise in writing. If anything related to our work fails within 90 days, you call us and Hal returns to make it right, no charge for the callback. As an independent FAAC service provider, we are not affiliated with or authorized by FAAC, and we cannot extend FAAC’s manufacturer warranty, but our own guarantee is plain and does not require anyone to huff about it. Call (817) 241-4067 if you’re unsure whether your current issue falls under a repair we previously performed.
For most access control issues, yes. Receiver replacements, keypad failures, and loose terminal connections are typically diagnosed and handled the same day we arrive, and we aim to be at your Fort Worth property within one business day of your call. Jobs that require a specialty FAAC board or a whole operator may take two to three days once the part is in hand, and we’ll tell you that before we start, not after.
We repair before we replace, full stop. If the motor is sound, the gearbox moves freely, and the board failure is isolated, we repair the specific fault and leave your FAAC operator in place. We only recommend replacement when the operator is at end of life on multiple fronts, and then we’ll show you the numbers for both options and let you choose. The last thing we want is to sell you a $2,000 operator when a $300 board is the real fix.
Yes, we install, repair, and replace phone entry modules and video intercom systems tied into FAAC operators across Fort Worth. Many of these use third-party intercom brands wired into the FAAC terminal block, and we have been squaring away that wiring long enough to know which combination plays nicely together before we bill you for anything. Call us and describe the behavior: no ring at the house, one-way audio, or door release that won’t fire. We can usually tell you where the fault is from that first call.
A well-installed FAAC system in the Fort Worth climate, with the cabinet mounted out of full afternoon sun and the hinge posts bearing the gate properly, should give you ten to fifteen years. The failures we see at the ten-year mark are boards and receivers, not the hydraulic or mechanical side, and those are repairable without a full swap. Units that fail early usually do because they were mounted in direct sun or the original post install was never right. That is the sort of sloppy work we get a little sore about when we see it, because the access control gets blamed for a problem it didn’t create.
Give me a call - that’s my real number, and I’ll pick up. (817) 241-4067.
Written by Hal Gatewood, Owner, Gatewood Fence & Gate at Gatewood Fence & Gate, serving Fort Worth and nearby areas.